You are here:

Projects

The Capstone Projects of the 2026 batch are presented below with their team members, supervisors, abstracts and project photographs.

  1. Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II
  2. Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters
  3. Design of a Cavitation Tunnel for Propeller Model Testing
  4. Design and Fabrication of a Towing Tank for Experimental Purposes
  5. Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat
  6. Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations
  7. Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II)
  8. Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0)
  9. Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter
  10. Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection
  11. Design and Development of a Mini-Scale Voith Schneider Propeller
Group 1

Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II

Team Members

  1. HAPUTHANTHRI H.D.S.K. (EG/2021/4542)
  2. WAIDYASINGHE I.P. (EG/2020/4258)
  3. ABEYNANDA U.A.D.D. (EG/2021/4380)
  4. BANDARA K.M.C.L (EG/2021/4431)

Supervisor: Eng. K.G.V.K. De Silva
Co-Supervisor: Dr. Sumith Baduge

Abstract

The increasing demand for sustainable and efficient energy solutions has encouraged the development of innovative wind energy technologies. This study focuses on the design and development of a Vortex-Induced Vibration (VIV) wind energy generator – Phase II, aiming to improve the performance and adaptability of a previously developed bladeless wind turbine prototype. Unlike conventional wind turbines, this system utilizes vortex shedding to induce oscillatory motion in a cylindrical mast, which is then converted into electrical energy.

In this phase, significant enhancements are introduced to overcome the limitations identified in the initial design. The PVC mast is replaced with a fiber-reinforced structure to improve stiffness, reduce weight, and achieve a more favorable natural frequency for resonance. Additionally, the energy conversion mechanism is upgraded by incorporating a piezoelectric system, enabling efficient power generation under low wind speed conditions. A key innovation in this phase is the implementation of a tuning mechanism, designed to adjust the structural natural frequency and maintain resonance across a wider range of wind speeds.

The study involves theoretical analysis, numerical simulations, and experimental validation to evaluate the system’s vibration characteristics, structural integrity, and energy output. The improved design demonstrates enhanced resonance behavior, increased operational range, and better energy harvesting capability compared to the previous model.

The outcomes of this research contribute to the advancement of compact, low-maintenance, and environmentally friendly wind energy systems, particularly suitable for urban and low-wind environments, supporting the transition toward sustainable energy solutions.

Project Photographs

Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 5Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 1Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 2Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 3Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 4Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 6Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 7Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 8Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 9Group 1 – Design and Development of a Vortex Induced Vibrating Wind Energy Generator – Phase II – photo 10
Group 2

Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters

Team Members

  1. ARACHCHI N.A.U.L.N. (EG/2021/4409)
  2. BANDARA T.G.K.C. (EG/2021/4438)
  3. CHIRANGA W.H.C. (EG/2021/4453)
  4. KUMARA S.H.A.M.J.P. (EG/2021/4627)

Supervisor: Eng. K.G.V.K. De Silva
Co-Supervisor: Eng. Hirun Seneviratne

Abstract

Sri Lanka’s growing energy demand and reliance on imported fossil fuels call for sustainable, locally available alternatives. With a long coastline and steady nearshore waves, the country holds a large but underused wave energy resource. In response, Group 02 of the Department of Marine Engineering and Naval Architecture, Faculty of Engineering, University of Ruhuna, undertook a capstone project to design and develop an Oscillating Wave Surge Converter (OWSC) for shallow coastal waters.

The device uses a bottom-hinged flap, 1.1 m high and 0.8 m wide, that swings back and forth with the horizontal surge of incoming waves. A power take-off system of chain, sprockets and a 1:200 gearbox drives an alternator to generate electricity. The team progressed from literature review and conceptual design to engineering calculations, CFD simulations and finite element analysis. The final design was modelled in SolidWorks and fabricated using galvanized steel, fibreglass and protective epoxy coating to resist marine corrosion. The design emphasises low cost and simple fabrication.

The prototype was deployed at sea in September 2026 and tested for about 60 minutes at three water depths, with an ESP32-based system recording current, voltage and power. Maximum power increased with depth, from 1.02 W at 0.65 m to 2.23 W at 0.80 m and 8.03 W at 1.0 m.

These results demonstrate the technical feasibility of small-scale wave energy conversion in Sri Lanka and provide a foundation for larger-scale coastal energy harvesting. Future work will add a flywheel to smooth the output and explore more efficient power take-off systems.

Project Photographs

Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 1Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 2Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 3Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 4Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 5Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 6Group 2 – Design and Development of an Oscillating Wave Surge Converter (OWSC) for Shallow Waters – photo 7
Group 3

Design of a Cavitation Tunnel for Propeller Model Testing

Team Members

  1. BHASHITHA J.H.G.P. (EG/2021/4444)
  2. BHARATHA P.K.G. (EG/2021/4443)
  3. MADUSHA W.D.R. (EG/2021/4663)
  4. KARUNASIRI K.P.K.K. (EG/2019/3628)

Supervisor: Dr. Sumith Baduge
Co-Supervisor: Eng. K.G.V.K. De Silva

Abstract

Cavitation is a complex hydrodynamic phenomenon that occurs when rapid pressure changes in a liquid lead to the formation and subsequent collapse of vapor bubbles. This process generates intense shockwaves that can cause significant damage to marine propellers, hydraulic systems, and other fluid machinery. The effects of cavitation include surface erosion, noise generation, vibration, and reduced operational efficiency, making it a critical concern in marine engineering. Currently, large-scale cavitation tunnels used for research are expensive to build and maintain, limiting their accessibility to only a few specialized institutions.

This project aims to address this gap by designing and developing a small scale, cost-effective cavitation tunnel specifically for propeller model testing. The tunnel will simulate real world hydrodynamic conditions to study cavitation inception, bubble dynamics, and their impact on propeller performance. Key design considerations include selecting durable materials resistant to cavitation erosion, ensuring stable flow conditions, and incorporating advanced instrumentation for accurate data collection. The project will integrate theoretical analysis with experimental validation, providing a practical research tool for academic institutions and small-scale industrial applications. Future work will focus on optimizing the tunnel’s performance through computational fluid dynamics (CFD) simulations and exploring advanced materials to enhance durability.

The successful completion of this project will provide a valuable research and testing tool for marine engineering applications. The cavitation tunnel will aid in the development of more efficient and durable propellers, contributing to fuel savings, improved vessel performance, and enhanced operational safety. Furthermore, the facility can serve as a platform for future research in hydrodynamics and fluid-structure interactions, benefiting both academia and the maritime industry.

Project Photographs

Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 1Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 2Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 3Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 4Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 5Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 6Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 7Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 8Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 9Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 10Group 3 – Design of a Cavitation Tunnel for Propeller Model Testing – photo 11
Group 4

Design and Fabrication of a Towing Tank for Experimental Purposes

Team Members

  1. MENAKA K.G.L.N. (EG/2021/4673)
  2. CHAMIKA A.M.S. (EG/2021/4450)
  3. FERNANDO W.S.M. (EG/2021/4515)
  4. INDULA W.J. (EG/2021/4563)

Supervisor: Dr. Sumith Baduge
Co-Supervisor: Eng. (Ms.) Anusara Wijerathna

Abstract

This capstone project focused on the design and fabrication of a cost-effective, small-scale towing tank to restore hydrodynamic testing capabilities in the Department of Marine Engineering and Naval Architecture, University of Ruhuna. The previous towing tank had become unusable due to the failure of its moving carriage system. To overcome this limitation, a fixed-carriage configuration combined with a controlled water-recirculation system was developed to simulate towing conditions without requiring a moving carriage. The design process involved a review of towing tank standards, hydrodynamic testing principles, and scaling laws, followed by concept generation and evaluation using engineering design methods.

A 1:200 Froude-scale model of a representative 76 m vessel was selected, and the tank dimensions were determined according to ITTC recommendations while maintaining an acceptable blockage ratio. Hydraulic calculations were performed to size the pump, piping, and flow-control system, and finite element analysis confirmed the structural safety of the tank and supporting frame. Polycarbonate was selected as the construction material because of its strength, transparency, and affordability. The completed system integrates a towing tank, tow truck, water-recirculation system, and a load-cell-based resistance measurement system with Arduino data acquisition. Preliminary experiments produced stable and repeatable results, demonstrating the system’s suitability for resistance and propulsion testing while providing an affordable, functional, and expandable facility for education and future marine hydrodynamics research.

Project Photographs

Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 1Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 2Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 3Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 4Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 5Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 6Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 7Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 8Group 4 – Design and Fabrication of a Towing Tank for Experimental Purposes – photo 9
Group 5

Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat

Team Members

  1. DESHAN H.G.U. (EG/2021/4472)
  2. HERATH A.W.R.I.G.H.D. (EG/2021/4548)
  3. KUMARASINGHE M.D.S. (EG/2021/4633)
  4. NILUKSHAN W.M.D. (EG/2021/4690)

Supervisor: Eng. H.G.D. Nadeepa
Co-Supervisor: Dr. Sumith Baduge

Abstract

This project presents the redesign and optimization of a Wageningen B-series propeller for a 15–20 m multi-day fishing vessel operating in Sri Lankan coastal waters. Small fishing boats commonly use standard B-series propellers selected using approximate methods, which often results in poor engine–propeller matching, reduced propulsion efficiency, higher fuel consumption, and increased cavitation risk. The aim of this project is to analyze vessel resistance, engine power characteristics, and operating conditions to determine optimal propeller parameters such as diameter, pitch ratio, blade area ratio, and rotational speed. A systematic design methodology based on propeller theory, performance charts, and hydrodynamic analysis will be applied to improve thrust and efficiency while maintaining safe cavitation limits. In addition to theoretical design, a scaled prototype of the redesigned propeller will be fabricated and tested to validate performance improvements. The expected outcome is an efficient and practical propeller design that reduces fuel consumption and enhances propulsion performance for small fishing vessels in Sri Lanka.

Project Photographs

Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 1Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 2Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 3Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 4Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 5Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 6Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 7Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 8Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 9Group 5 – Redesign and Performance Optimization of a Wageningen B-Series Propeller for a Typical 15–20 m Sri Lankan Multiday Fishing Boat – photo 10
Group 6

Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations

Team Members

  1. FERNANDO K.S.P.D. (EG/2021/4509)
  2. KUMARA R.A.K.N. (EG/2021/4625)
  3. MADHAVAN A. (EG/2021/4652)
  4. NIRODHA K.D.A.L. (EG/2021/4694)

Supervisor: Eng. K.G.V.K. De Silva
Co-Supervisor: Eng. Hirun Seneviratne

Abstract

Oil pollution in harbor basins, resulting from ship bunkering, fuel transfers, bilge related discharges, machinery leakage, and accidental spills, poses a significant threat to marine ecosystems and coastal environments. This project focuses on the design and fabrication of a cost-effective disc-type oil skimmer for recovering floating oil from harbor waters, particularly in small and medium-scale port environments in Sri Lanka.

The proposed system operates on the principle of oleophilicity, whereby rotating discs collect oil adhering to their surfaces as they pass through the floating oil layer. Scraper blades remove the accumulated oil and direct it into a collection trough for recovery. The prototype incorporates aluminium discs, a supporting frame, twin aluminium pontoons, a shaft and bearing arrangement, a chain-drive mechanism, and a motor. The project involved a literature review, development and selection of conceptual designs, engineering calculations, three-dimensional modelling using SolidWorks, finite element analysis (FEA), fabrication, assembly, and experimental performance evaluation.

Testing was conducted to assess flotation stability, structural integrity, oil recovery rate, and the effectiveness of the disc and scraper mechanism. The prototype demonstrated satisfactory flotation stability and structural performance under calm harbor conditions. During controlled recovery trials, a maximum oil recovery rate of 0.180 L/s was achieved, compared with the theoretical design target. The lower recovery performance was primarily associated with the limited oleophilic properties of the substitute disc coating.

The project demonstrates the feasibility of developing a locally fabricable oil recovery device for harbor applications. Further improvements to disc surface properties, drive transmission, and operating conditions are recommended to enhance recovery efficiency and operational reliability.

Project Photographs

Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 1Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 2Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 3Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 4Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 5Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 6Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 7Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 8Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 9Group 6 – Design and Fabrication of a Disc Type Oil Skimmer for Harbor Basin Operations – photo 10
Group 7

Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II)

Team Members

  1. GUNATHILAKA R.D.S.D. (EG/2021/4532)
  2. LAKSHAN S.C.K. (EG/2021/4641)
  3. RANAWEERA R.A.K.D. (EG/2021/4743)
  4. REJINOLD K.T.D.H.H. (EG/2021/4759)

Supervisor: Eng. T.D. Jayasekera
Co-Supervisor: Eng. (Ms.) Anusara Wijerathna

Abstract

Conventional unmanned aerial vehicles (UAVs) face significant operational limitations in maritime environments due to their inability to take off from or land on water. This project addresses this capability gap through the design, fabrication, and testing of a small-scale, remote-controlled Wing-In-Ground (WIG) craft optimized for marine surveillance. The primary objective was to develop a functional prototype that leverages the aerodynamic efficiencies of ground effect flight while maintaining robust hydrodynamic performance.

The design process utilized a combination of theoretical analysis, 3D CAD modeling, and computational fluid dynamics (CFD) simulations. A stepped, V type trimaran hull has been chosen to improve stability and better hydrodynamic performance, especially by making things better pressure distribution and lower drag properties. Profiles of airfoils including NACA 4412 and NACA 0012 have been analyzed to evaluate their suitability for generating lift and structural simplicity. The prototype is made by 3D printing.

Project Photographs

Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 1Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 2Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 3Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 4Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 5Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 6Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 7Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 8Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 9Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 10Group 7 – Design of a Small-Scale Remote-Controlled Wing-in-Ground Craft (Phase II) – photo 11
Group 8

Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0)

Team Members

  1. SAHABANDU D.S.R.L. (EG/2021/4772)
  2. JAYAPATHMA J.H.M.P.S. (EG/2021/4570)
  3. LIYANARACHCHI L.T.S. (EG/2021/4647)
  4. MADURANGA K.D.P.H. (EG/2021/4660)
  5. PREMATHILAKA H.W.J.S. (EG/2021/4728)

Supervisor: Eng. Hirun Seneviratne
Co-Supervisor: Eng. T.D. Jayasekera

Abstract

The growing demand for sustainable energy has encouraged the development of offshore wind technologies capable of operating in diverse marine environments. This project presents the design, development, simulation, fabrication, and field testing of AusterGen 1.0, a small-scale floating offshore Horizontal Axis Wind Turbine (HAWT) integrated with a SPAR-type floating platform, targeting the low-to-moderate wind conditions of Sri Lanka’s southern coast, where average wind speeds are approximately 4 m/s. The study focuses on aerodynamic performance, structural integrity, hydrodynamic stability, and integrated system operation.

Rotor aerodynamic characteristics were evaluated using Blade Element Momentum (BEM) analysis in QBlade, while structural simulations and coupled aero-hydrodynamic analyses supported the design process. The prototype incorporated a fabricated floating platform, ballast system, mechanical power transmission, yaw mechanism, and an ESP32-S3-based monitoring and pitch-control system. Experimental testing demonstrated a maximum electrical power output of 12.64 W, with an average output of approximately 5.17 W, exceeding the initial 5 W prototype target. During the final near-shore sea trial, the system successfully operated in a marine environment, recording a maximum output of 1.56 W under weak and intermittent wind conditions.

The results demonstrate the feasibility of integrating aerodynamic, mechanical, electrical, control, and floating-platform systems into a functional prototype. Further development should prioritize improved platform stability, sensor accuracy, energy storage, vibration control, and testing in deeper water under more representative offshore conditions.

Keywords: Floating Offshore Wind Turbine, SPAR Platform, HAWT, QBlade, Pitch Control, Offshore Renewable Energy

Project Photographs

Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 1Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 2Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 3Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 4Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 5Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 6Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 7Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 8Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 9Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 10Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 11Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 12Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 13Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 14Group 8 – Design, Development and Field Testing of a Spar Type Floating Offshore Wind Turbine (AusterGen 1.0) – photo 15
Group 9

Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter

Team Members

  1. JEROSHAN A.A.P.A. (EG/2021/4591)
  2. MADHUSHA R.N.D.N. (EG/2021/4657)
  3. NIMNATH D.P. (EG/2021/4692)
  4. SATHSARA M.P.P. (EG/2021/4791)

Supervisor: Eng. Hirun Seneviratne
Co-Supervisor: Eng. H.G.D. Nadeepa

Abstract

This project presents the design, development, numerical assessment, fabrication and field testing of a point absorber-type onshore wave energy converter intended for small-scale renewable-energy generation in Sri Lankan coastal conditions. The final system uses a hemispherical-bottom floater, an articulated shore-supported frame, a rack-and-pinion power take-off, gearbox, generator and electrical measurement circuit. Hydrodynamic assessment was carried out using ANSYS AQWA, including floater-geometry comparison and final irregular-wave time-response analysis, while finite element analysis was used to verify the structural response of the supporting frame. The final fixed support frame produced a maximum von Mises stress of 39.39 MPa against the 172.3 MPa yield strength used in the model, corresponding to a factor of safety of 4.37 and a maximum displacement of 0.4972 mm.

The prototype was then fabricated, integrated and deployed at the jetty near the Southern Maritime Training Institute in Galle on 28 September 2026. During the principal field-test telemetry run, 2,627 measurements were recorded and the highest measured electrical values were 14.496 V, 0.1444 A and 2.0932 W. The field test confirmed the complete conversion path from wave-induced floater motion through the mechanical transmission to measurable electrical generation under sheltered and irregular coastal conditions. The 30 W value remains the prototype design target rather than the measured output of this field trial.

The completed work demonstrates the operational feasibility of the proposed onshore point absorber and identifies further optimization of the power take-off, electrical loading and site-specific wave measurement as the main directions for future development.

Project Photographs

Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 1Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 2Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 3Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 4Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 5Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 6Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 7Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 8Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 9Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 10Group 9 – Design, Development and Field Testing of a Point Absorber Type Onshore Wave Energy Converter – photo 11
Group 10

Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection

Team Members

  1. WIJESOORIYA W.A.A.D. (EG/2021/4879)
  2. RATHNAMALALA RBMB (EG/2021/4749)
  3. RANMUTHU T.G.K. (EG/2021/4746)
  4. WIJAYASEKARA M.S.L. (EG/2021/4865)

Supervisor: Eng. (Ms.) Anusara Wijerathna
Co-Supervisor: Eng. T.D. Jayasekera

Abstract

The structural integrity of a ship’s hull is a critical factor influencing safety, operational efficiency, and compliance with maritime regulations. Conventional inspection methods, including dry-docking and diver-based surveys, are often expensive, time-consuming, and associated with safety risks. This project proposes the design and development of a compact submersible Remotely Operated Vehicle (ROV) specifically tailored for efficient underwater hull inspection, with primary emphasis on structural design optimization and operational performance.

The study focuses on redesigning the ROV body structure to achieve improved stability, reduced hydrodynamic drag, and enhanced maneuverability, enabling safe and controlled operation near complex hull geometries. Attention is given to achieving balanced buoyancy, effective thruster configuration, and a streamlined form that supports precise movement and positioning. In addition, the integration of advanced electronic sensing technologies, including high-definition imaging systems and sonar-based sensors, allows accurate detection and monitoring of surface defects and marine growth.

A six-thruster propulsion arrangement is used to improve maneuverability: two aft thrusters provide surge motion, two centrally positioned vertical thrusters control depth, and two forward thrusters angled inward at 45 degrees provide yaw control. Buoyancy, stability, propulsion requirements, and waterproofing are considered in the design to support reliable underwater operation. The control system integrates an Arduino Uno, joystick inputs, electronic speed controllers, and an inertial measurement unit to manage thruster operation. An onboard camera provides live visual feedback, which is transmitted to a surface laptop through a tethered communication system. The tether also carries low-voltage DC power and control signals, supporting continuous operation without relying solely on onboard batteries.

The proposed design aims to improve inspection efficiency while minimizing operational risks and reliance on human divers. Overall, this project contributes to the development of a cost-effective and practical solution for underwater hull inspection, emphasizing structural performance, safety, and efficiency in real-world maritime applications.

Project Photographs

Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 1Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 2Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 3Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 4Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 5Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 6Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 7Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 8Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 9Group 10 – Design of an Autonomous Submersible Remotely Operated Vehicle (ROV) for Hull Inspection – photo 10
Group 11

Design and Development of a Mini-Scale Voith Schneider Propeller

Team Members

  1. KUMARA T.V.C.C. (EG/2021/4628)
  2. PERERA G.V.D.P. (EG/2021/4709)
  3. PUSHPADEWA H.G.T.P. (EG/2021/4730)
  4. WANATHUNGA I.G.J.U. (EG/2021/4846)

Supervisor: Eng. T.D. Jayasekera
Co-Supervisor: Dr. Sumith Baduge

Abstract

The Voith Schneider Propeller (VSP) is a highly versatile cycloidal propulsion system capable of generating instantaneous thrust in any horizontal direction without a rudder, though small-scale laboratory models remain scarce for academic and educational research. To address this gap, Group 04 of the Department of Marine Engineering and Naval Architecture, Faculty of Engineering, University of Ruhuna, undertook a capstone project to design, fabricate, and test a mini-scale VSP prototype.

The system features a 200 mm rotor diameter equipped with five vertically oriented hydrofoil blades based on a symmetrical NACA 0015 profile, spanning a height of 128 mm. Utilizing a fully mechanical crank-pin linkage system and a 1:2.5 bevel gear reduction drive, the prototype converts rotational input into synchronized cyclical blade pitching. Major components were 3D-printed using PLA+ alongside structural aluminium and precision rolling-element bearings to minimize cost, weight, and mechanical play.

The assembled prototype was mounted onto a custom testing rig and evaluated under controlled fresh water conditions across rotational speeds ranging from 200 RPM to 400 RPM. Static bollard pull measurements recorded using a digital spring balance demonstrated a clear relationship between increasing rotational speed and total thrust output, yielding 10.68 N at 350 RPM with a constant non-dimensional thrust coefficient (KT) of 0.60.

These experimental results prove the technical feasibility of low-cost, small-scale cycloidal propulsion systems for academic environments and establish a solid foundation for future studies. Recommended future work includes transitioning to dynamic towing tank testing, exploring advanced composite manufacturing for sharper blade trailing edges, and integrating microcontrollers for automated electronic thrust vectoring.

Project Photographs

Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 1Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 2Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 3Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 4Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 5Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 6Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 7Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 8Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 9Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 10Group 11 – Design and Development of a Mini-Scale Voith Schneider Propeller – photo 11
S/N Registration Number Students Name Individual Project Name
1 EG/2021/4743 Ranaweera R.A.K.D. Design of a Profile Marking Device for Small Scale Fixed Pitch Propellers.
2 EG/2021/4438 Bandara T.G.K.C. Design of external gear type positive Dispalcement pump
3 EG/2021/4673 Menaka K.G.L.N Design and Development of an automated confined-space rescue tripod with powerd winch and fall – arrest system
4 EG/2021/4641 Lakshan S.C.K. Design and development of an improved catch handling device for vessel mounted operation
5 EG/2021/4692 Nimnath D.P. Design Coupled Dynamic Response Analysis, and Optimization of an Offshore Floating Wind Turbine Platform
6 EG/2021/4570 Jayapathma J.H.M.P.S Design a modular deck panel using advanced composites for weight reduction
7 EG/2021/4532 Gunathilaka R.D.S.D Design of a high head single impellor centrifugal pump
8 EG/2021/4657 Madhusha R.N.D.N. Design of hybrid locomotion mechanism for shoreline inspection amphibous Vehicle
9 EG/2021/4730 Pushpadewa H.G.T.P. Design of a propulsion system for a small scale wing in ground effect craft for coastal operations
10 EG/2021/4663 Madusha W.D.R Design of a human powered propeller driven canoe for inland waters
11 EG/2021/4450 Chamika A.M.S. Design and development of a Hybrid Shock-Absorbing System for Mooring Lines of Ships
12 EG/2021/4690 Nilukshan W.M.D. Design of a waste heat recovery desalination unit for small vessels
13 EG/2021/4709 Perera G.V.D.P. Design of a small water-jet propulsion unit for small boats
14 EG/2021/4749 Rathnamalala R.B.M.B. Design of a tidel driven turbine generator for small channel
15 EG/2021/4652 Madhavan A. Design of a Compact MARPOL-Compliant Marine Sewage Treatment System for Small Coastal Vessels
16 EG/2021/4628 Kumara T V.C.C. Design of a collection device for plastic nurdles from coastlines
17 EG/2021/4694 Nirodha K.D.A.L. Design of a Compact Bilge Water Filtration System for Small Vessels
18 EG/2021/4515 Fernando W.S.M Design of a Automated Net Hauler for small fishing boats
19 EG/2021/4633 Kumarasinghe M.D.S. Design of a wave powered Floating Marker Bouy for Small Channels
20 EG/2021/4472 Deshan H.G.U. Design of a Power Transmission System of an Offshore Wind Turbine
21 EG/2021/4627 KUMARA S.H.A.M.J.P. Design of internal gear type positive Displacement pump
22 EG/2019/3628 Karunasiri K.P.K.K. Designing an ergonomic device for moving postoperative patients in hospitals
23 EG/2021/4759 REJINOLD K.T.D.H.H Design of a multi-lobe type Positive Displacement Pump
24 EG/2021/4443 Bharatha P.K.G Design of a variable pitch marine propulsion system for small craft.
25 EG/2021/4791 SATHSARA M.P.P Design of lower body exoskeleton
26 EG/2021/4660 Maduranga K.D.P.H Design of a retractable landing gear for Land Takeoff and Water Landing of a Light Amphibious Seaplane UAV
27 EG/2021/4728 Premathilaka H.W.J.S Design of a fishing boat with a V-shape hull and high load- bearing capacity
28 EG/2021/4509 Fernando K.S.P.D Design of a Motor Operated Spill-Resistant Dangerous Goods (DG) Pallet Trolley for Quayside Operations
29 EG/2021/4453 Chiranga W.H.C Design CFD based hydrodynamic analysis and optimization of a wave powered marine energy conversion system
30 EG/2021/4846 Wanathunga I.G.J.U. Design of a Floating Waste Collection Skimmer for Harbor Surface Debris
31 EG/2021/4542 Haputhanthri H.D.S.K . Design a short-route ferry hull considering stability, passenger comfort, and fuel efficiency
32 EG/2020/4258 Waidyasinghe I.P. Design of a telescopic fruit harvester
33 EG/2021/4409 ARACHCHI N.A.U.L.N Design a high performance triple offset butterfly valve operated by a wheel handle
34 EG/2021/4444 Bhashitha J.H.G.P. Design of a Steering Gear Mechanism of a Yacht
35 EG/2021/4746 Ranmuthu T.G.K Design of a hydraulic type capstan
36 EG/2021/4431 Bandara K.M.C.L. Design of a Transmission mode switching mechanism for amphibious bike-jet ski hybrid
37 EG/2021/4380 Abeynanda U.A.D.D Design of a Electric type capstan
38 EG/2021/4548 HERATH A.W.R.IG.H.D Design and development of a nearshore ocillating body wave energy converter
39 EG/2021/4591 Jeroshan A.A.P.A Desgin of a Catamaran Based Sea Weed Harvesting and Replanting Machine
40 EG/2021/4879 Wijesooriya W.A.A.D Foldable deck cover and mechanism for Yachts
41 EG/2021/4772 SAHABANDU D.S.R.L. Design & Development of a Vertical Axis Wind Turbine for Small Power Generation in Hi-ways
42 EG/2021/4625 Kumara R.A.K.N. Design and development of Belt Type Oil Skimmer
43 EG/2021/4665 Wijayasekara M.S.L Desing and optimization of a PTO drive train for a flap type wave energy converter.
44 EG/2021/4563 Indula W.J. Design and development ofa multi modal hull cleaning system
45 EG/2021/4647 Liyanarachchi L. T. S Design of retractable wing mounted pontoons for a flyingboat